Prices for Redwood Tongue and Groove Siding depend on board quality, thickness, finish, and installation scope. This article breaks down the cost, offers practical ranges in USD, and highlights drivers that influence the final price for Redwood Tongue and Groove Siding projects.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Material (unfinshed Redwood, 1×6 or 1×8) | $2.50 | $5.50 | $8.50 | Per lineal foot; varies by grade |
| Material (finished, prefinished, clear grade) | $4.00 | $7.50 | $12.00 | Per sq ft equivalent |
| Labor (installation, carpentry) | $3.50 | $6.50 | $11.50 | Per sq ft |
| Labor Time (typical project) | 5 days | 7 days | 10 days | Includes prep and nail/finish work |
| Estimated Total Installed Cost | $10 | $18 | $28 | Per sq ft installed |
| Permits/Delivery/Disposal | $0 | $1.50 | $3 | Depends on locality |
Cost Range for Redwood Tongue and Groove Siding Per Square Foot
Typical installed pricing falls in the $12-$22 per square foot band when considering both materials and labor for standard 1×6 or 1×8 tongue and groove boards, with higher-end clear grades and prefinished surfaces pushing toward the upper end. The range reflects midwestern to coastal labor rates and standard site access. Assumptions: standard 2×4 wall framing, typical weather, normal access, and reasonable lead time.
Major Cost Components in the Redwood Tongue and Groove Siding Quote
The quote breaks down into four to six key parts. Materials plus labor drive the bulk of the price, while permits, delivery, and disposal add modest adds. The following table shows typical components and ranges.
| Component | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials (board cost per sq ft) | $2.50 | $5.50 | $8.50 | Includes grade variation |
| Labor (installation per sq ft) | $3.50 | $6.50 | $11.50 | Edge work and trimming |
| Delivery/Handling | $0.50 | $1.50 | $3.00 | Distance-based |
| Permits/Inspections | $0 | $1.00 | $2.50 | Local codes vary |
| Finish/Sealing (optional) | $0.50 | $1.50 | $3.00 | Stain or varnish included |
Variables That Shift Redwood Tongue and Groove Siding Pricing
Grade and thickness of the Redwood board directly affect material cost, with clear grades at the high end. Project scope and wall area influence labor hours and crew size, especially for multi-story or complex detailing. Typical thresholds include 500-700 sq ft of siding as a practical break-even for hiring a dedicated crew versus hand-placing panels.
Specifics That Change the Final Quote: Board Grade and Thickness
Colorful and straight-grain clear redwood boards cost more per sq ft than standard grades. For example, 1×6 boards in common grades might be $2.50-$5.50 per linear foot, while premium 1×8 clear boards could push material closer to $8-$12 per linear foot, which translates to higher installed costs overall when spanning large facades.
Regional Price Variations for Redwood Tongue and Groove Siding
Coastal markets typically show higher installed prices than inland regions due to shipping and demand. West Coast installations often run 5-15% higher than the national average, while the Midwest might sit closer to the average. Regional weather impact can add small costs for stabilization or sealant choices.
Labor Rate Ranges by Job Size and Crew Configuration
Labor can swing widely based on crew size and local wages. A small crew may charge $4-$7 per sq ft for basic installation, while a larger team with higher efficiency and careful detailing can run $7-$11 per sq ft. Schedule constraints or seasonal demand can introduce minor surcharges.
Per-Unit and Per-Foot Calculations for Redwood Siding
When pricing by unit, common factors include per square foot installed or per lineal foot of board. For rough guides, expect material plus labor to land around $12-$22 per sq ft after finishing and trim considerations. Always confirm whether the quote includes fasteners, backer boards, and flashing.
Add-Ons and Upgrades That Impact the Final Price
Extra finishes, moisture barriers, and primer/sealer can add $0.50-$2.00 per sq ft depending on quality and number of coats. If decorative trim or corner boards are required, budget an additional $1.00-$3.50 per sq ft for labor and materials. Poor surface prep or irregular surfaces can raise costs further.
Practical Ways to Reduce the Redwood Tongue and Groove Siding Price
Scope control and precise measurements help avoid waste. Consider standard sizes and fewer cuts, plan delivery during off-peak seasons, and compare multiple quotes. If repairs are feasible, replacing damaged sections rather than full wall re-side can substantially cut costs. Bundling painting or sealing with the siding project can yield modest savings.
Project Scope Scenarios and Their Price Impact
Smaller, single-story homes with straightforward walls may land on the lower end of the ranges, around $10-$14 per sq ft installed. Mid-range homes with moderate detail and trims typically hit $15-$20 per sq ft. Large, multi-story or rustic applications with premium grades can exceed $22 per sq ft installed.
One-Page Quick Quote: Example Scenarios
Two real-world examples help set expectations. Example A: 800 sq ft of 1×6 Redwood Tongue and Groove, standard grade, mid-range fasteners, no finish. Installed cost ranges from $9,600-$14,000 depending on regional labor. Example B: 1,200 sq ft with premium grade 1×8, prefinished surface, and moisture barrier. Installed costs may run $18,000-$28,000.
Table of Typical Installed Rates by Region
| Region | Material/Board | Labor | Total Installed (per sq ft) |
|---|---|---|---|
| Northeast | $4.50 | $6.50 | $11.00 |
| Midwest | $4.00 | $5.50 | $9.50 |
| South | $3.75 | $5.00 | $8.75 |
| West | $4.75 | $6.75 | $11.50 |
