Limestone 57 pricing refers to the cost per ton for crushed limestone sized around 57 stone, commonly used for drainage, driveways, and base material. Buyers typically see a range driven by quarry location, freight, and quality. The price per ton, and any delivery fees, are the main cost drivers for projects using 57 limestone.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Delivered price per ton | $12 | $22 | $40 | Regional variation affects base freight |
| Stockpile/pickup price per ton | $12 | $18 | $28 | Available at quarries; excludes delivery |
| Delivery surcharge per load | $30 | $65 | $150 | Based on distance and access |
| Minimum load fee | $20 | $40 | $100 | Often applies to small orders |
| Tax considerations | $0 | $3 | $6 | Depends on state and county |
| Estimated total project cost (tonnage assumed 10 tons) | $120 | $260 | $520 | Includes delivery; excludes site prep |
Assumptions: Midwest labor rates, standard bulk limestone, normal site access, typical load sizes, and standard delivery routes.
Typical Price Range for Limestone 57 Per Ton
Buyers usually pay $12-$40 per ton for Limestone 57, with average delivery pricing around $22-$28 per ton in many regions. The total per-ton price reflects quarry cost, material quality, and freight distance. If a project requires more than 20 tons, some suppliers offer reduced per-ton freight or a bundled delivery rate. For small orders, expect minimum charges that can raise the effective per-ton cost.
Major Cost Components in Limestone 57 Delivery
The quote breaks down into four to six components, with freight as the largest variable. Typical cost components include Materials, Delivery/Disposal, Taxes, and Optional Permits or Fees. The following table shows a representative breakdown you’ll see on a bid.
| Component | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials (Limestone 57) | $12 | $22 | $40 | Base material price at quarry |
| Delivery/Transport | $30 | $65 | $150 | Distance and access drive freight |
| Taxes | $0 | $3 | $6 | State/local taxes apply |
| Minimum charge | $20 | $40 | $100 | Small orders may incur a fee |
| Permit/Access fees | $0 | $5 | $20 | Only for special site access |
Assumptions: standard bulk delivery, no surcharges for weekend delivery, normal road access.
Regional Variations by U.S. Market
Prices vary by region due to quarry proximity and trucking lanes. In the Southeast, delivered prices often sit near $16-$28 per ton, while the Midwest and Northeast can range from $20-$40 per ton after freight. Western markets may show similar ranges but with higher delivery costs due to terrain and fuel. Expect higher per-ton rates in rural, hard-to-reach areas and lower rates near large quarries.
Labor and Equipment Impact on 57 Limestone Cost
Labor and equipment charges affect handling and placement of the rock. If the job includes spreading, raking, and compacting, you’ll see additional hourly rates or crew-day charges. Typical rates for site labor range from $75-$125 per hour per crew, depending on location and crew size. Equipment rental (loader, skid-steer, compactor) adds $100-$300 per day, or a bundled equipment rate with operator).
Size, Distance, and Transport as Key Drivers
Distance from quarry and load size dominate freight costs. For a 10-ton job, delivery fees can range from $30-$150 per load depending on distance (10-50 miles typical) and access. Larger loads reduce per-ton freight in many cases, while remote sites can push costs higher. Freight surcharges for weather or peak season can add 5-15% to the subtotal.
Ways to Reduce Limestone 57 Expenses Without Compromising Quality
Careful scope control and timing can trim costs. Consider buying a bundled delivery and offload service, plan for off-peak scheduling, and request a single-invoice quote for all loads. If possible, combine orders with adjacent projects to maximize load efficiency, or select a close quarry to reduce trucking distance. Choosing similar rock size and grading can avoid re-handling charges at the site.
Per-Ton vs Per-Yard Pricing for Limestone 57
Understand the conversion to plan material budgets accurately. One ton of limestone 57 typically yields about 0.4 cubic yards, depending on compaction and moisture. For planning, use 2.5-3 tons per 100 square feet for a 4-inch layer on a driveway, or 4-6 tons per 100 square feet for sub-base depth. Price per ton will translate to per-yard costs with the conversion factor.
Common Add-Ons and Prep Work That Change the Quote
Site prep and delivery logistics can shift the final price. Add-ons include unloading labor, wheelbarrow or skid-steer service, contaminated rock removal, and on-site spreading. If the site requires grading, ramping, or compaction, expect additional labor hours or equipment fees. Some bids also include disposal of excess material or planed topsoil replacement, which can affect the total.
