Typical costs for GE oven igniter replacement depend on the igniter type, model, and whether a diagnostic visit is needed. The main cost drivers are the part price, labor time, and any required accessories or additional fixes. This guide provides clear cost ranges and practical budgeting notes for U.S. buyers.
Assumptions: region, GE model compatibility, standard diagnostic assessment, and normal labor hours.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Part (Igniter or igniter kit) | $25 | $70 | $140 | Glow-bar or hot-surface igniter varies by model |
| Labor | $80 | $150 | $280 | Isolated repair vs. multi-visit diagnosis |
| Diagnostics / Service Call | $0 | $60 | $120 | Many shops waive if you proceed with repair |
| Additional Parts (wiring, connectors, reflectors) | $5 | $25 | $60 | Occasional extras for older models |
| Delivery / Disposal | $0 | $10 | $25 | Depending on supplier and locale |
| Taxes & Permits | $0 | $10 | $20 | Taxed as applicable |
| Estimated Total | $110 | $260 | $520 | Assumes diagnosis followed by ignition replacement |
Overview Of Costs
Cost ranges reflect part price, labor, and possible extras for GE ovens. The total project cost commonly falls in the low hundreds for a straightforward igniter swap, while complex or older units can push into the mid-to-high hundreds. Per-unit pricing helps buyers compare parts costs quickly, with a typical igniter kit ranging from $25 to $140 and labor from $80 to $280 depending on complexity and regional rates.
data-formula=”labor_hours × hourly_rate”> A standard service call may be bundled with the repair, or priced separately if the technician requires a preliminary diagnostic visit. For major GE models with unique igniter assemblies, expect the higher end of the range due to compatibility checks and potential subassembly needs.
Where The Money Goes
The cost breakdown below uses common components of the replacement job. Assumptions include a single-igniter replacement on a standard GE gas or electric oven. If the oven has dual igniters, a broiler-specific part, or a sealed burner assembly, prices can shift up accordingly.
- Materials: Part(s) and any required adapters or connectors
- Labor: Time to access the igniter, remove old parts, install the new assembly, and test operation
- Equipment: Tools and any diagnostic devices used on site
- Permits: Usually not required for residential range work
- Delivery/Disposal: Shipping fees or waste removal if a replacement is purchased online
- Warranty: Some parts include a limited warranty; labor warranties vary by shop
- Taxes: Applicable sales tax
What Drives Price
Igniter type and model compatibility is the primary price driver. GE gas ovens may use glow-bar or hot-surface igniters; newer or high-end models could require specific OEM parts. A second driver is labor time and crew qualification; complex access behind panels, interior panels, or convection modules increases hours. Regional wage differences also affect total costs, with urban areas generally higher than rural markets.
Other notable factors include diagnostic requirements and any related fixes (thermostat recalibration, control board inspection, or wiring repair) performed during the same visit. Some shops offer a bundled diagnostic with the repair, while others bill separately if the diagnosis does not lead to an immediate part replacement.
Regional Price Differences
Prices vary by region due to labor markets and shipping costs. In the United States, typical ranges reflect urban, suburban, and rural differences.
- West Coast / Northeast urban areas: Part of the high end plus labor around the 60th percentile
- Midwest / Southeast suburban areas: Moderate pricing, near average
- Rural regions: Generally lower labor rates, may see slightly lower total
Labor & Installation Time
Time estimates for igniter replacement are usually short, but complications can extend the job. A straightforward install often takes about 1–2 hours; more complex access or dual igniters can require 3–4 hours. Labor rates commonly range from $60 to $140 per hour, depending on the region and technician experience.
When scheduling, consider the potential for a brief diagnostic fee if the problem is not immediately evident. If the diagnostic is waived upon repair, the effective total can be lower than a separate diagnostic charge.
Additional & Hidden Costs
Hidden or optional costs may appear in some scenarios. Delivery or shipping fees apply when parts are ordered online or from remote distributors. Wiring assessments or small component replacements can add modest amounts but are sometimes bundled with the main repair. Finally, extended warranties or service plans may alter the long-term ownership cost, though they typically affect upfront pricing rather than the immediate replacement bill.
Real-World Pricing Examples
Three scenario cards illustrate common outcomes for GE oven igniter replacement. These examples assume standard residential kitchens and typical GE models with accessible igniter assemblies.
-
Basic: One igniter replaced on a standard GE gas oven; no additional fixes.
- Parts: $30
- Labor: 1 hour @ $90
- Diagnostics: $0 (waived with repair)
- Delivery/Taxes: $0–$15
- Total: $120–$150
-
Mid-Range: Igniter kit plus minor wiring check; one additional component replaced if needed.
- Parts: $70
- Labor: 1.5 hours @ $95
- Diagnostics: $60
- Delivery/Disposal: $10
- Total: $260–$300
-
Premium: Igniter replacement with model-specific kit and an auxiliary control board check.
- Parts: $120
- Labor: 2.5 hours @ $110
- Diagnostics: $120
- Delivery/Disposal: $15
- Total: $370–$520
Assumptions: residential kitchen, GE oven, standard access, and no major burn damage or gas line concerns.
