Homeowners often compare Everlast and Hardie siding to estimate total costs, including materials and installation. Key cost drivers include material type, panel size, labor time, smooth vs textured finishes, and removal of old siding. The following guide presents practical price ranges in USD and clarifies what affects the bottom line. Cost and price considerations are central to choosing between Everlast and Hardie siding.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Material (per sq ft) | $2.50 | $4.50 | $7.50 | Everlast tends to be lower; Hardie higher due to fiber cement |
| Installed (per sq ft) | $6.50 | $9.50 | $14.50 | Includes labor, basic trim, and nails |
| Labor Time (per 1,000 sq ft) | 8–12 hrs | 12–18 hrs | 22–28 hrs | Fibers cement requires longer cuts |
| Removal/Disposal (per sq ft) | $0.25 | $0.75 | $1.50 | Old siding disposal adds to cost |
| Seam/Finish Options | $0.50 | $1.50 | $3.00 | Textured vs smooth and color options |
Overview Of Costs
Assumptions: region, house size, and crew rates vary; Everlast and Hardie costs reflect typical midwestern to southeastern markets. The price gap between Everlast and Hardie is driven by material composition, installation complexity, and warranty terms. For an average 1,500–2,000 sq ft house, installed costs typically range from $9,000 to $28,000 depending on product choice and project specifics. In general, Everlast siding might land in the lower end of the range, while Hardie fiber cement sits toward the higher end. Overall, Homeowners should expect $6–$14 per sq ft installed for Everlast and $9–$15 per sq ft installed for Hardie, with variations by region and project scope.
Cost Breakdown
Material costs include product itself and color options, with Everlast typically cheaper per square foot than Hardie fiber cement. Labor and installation dominate total cost for both options, especially on multi-story homes or intricate trim. The table below breaks down a representative project at 1,800 sq ft, assuming standard stucco-free walls and basic window/door openings.
| Category | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials | $3,600 | $8,100 | $12,600 | Everlast often lower; Hardie higher per sq ft |
| Labor | $5,400 | $9,900 | $15,300 | Includes installation crew and overlap work |
| Materials & Delivery | $100 | $600 | $1,200 | Delivery to site varies by distance |
| Permits/Inspections | $0 | $300 | $1,000 | State and local requirements |
| Disposal/Removal | $200 | $900 | $2,400 | Old siding disposal included |
| Warranty/Overhead | $0 | $600 | $1,800 | Project margin and coverage |
Assumptions: region, specs, labor hours.
What Drives Price
Material composition determines durability and appearance. Fiber cement (Hardie) is heavier, requires longer install times, and is more color-stable, which increases labor and equipment needs. Everlast siding, typically a vinyl-based or composite alternative, weighs less and installs faster in many layouts. data-formula=”labor_hours × hourly_rate”>
Installation complexity affects price. Multi-story homes, complex gables, and extensive trim increase hours and risk, raising labor rates and necessitating specialty tools. For Hardie, seam finishing and caulking are more time-consuming, often adding to both materials waste and labor.
Regional market variations shift price expectations. Urban markets tend to have higher labor rates and permit costs, while rural areas may save on disposal and travel time but incur limited contractor availability.
Ways To Save
Shop with regional pricing in mind. Compare three local bids to gauge typical ranges and look for one price that covers materials, installation, and disposal. Consider crew experience with fiber cement for Hardie and with vinyl/composite systems for Everlast to avoid rework.
Leverage off-season timing. Contractors sometimes run promotions or lower rates outside peak remodeling seasons, particularly for exterior projects that require dry weather windows. Plan around mild months to reduce weather delays.
Bundle upgrades and warranties. A longer warranty on colorfast finishes or impact-resistant trims can prevent future touch-ups and repainting costs, effectively lowering life-cycle cost even if upfront price is higher.
Regional Price Differences
Prices vary by region due to labor supply, material transport, and local codes. In the Southeast, installed costs may run on the lower end of the ranges, while the Northeast often sees higher labor and permit costs. The Midwest typically falls between these extremes, with rural areas sometimes cheaper than urban cores. Consider a ±10–20% delta when moving between regions and suburbs versus urban centers.
Labor & Installation Time
Labor time depends on wall complexity, height, and the presence of features like riveted channels or intricate corners. Everlast generally requires less cutting and faster fastening, reducing hours. Hardie fiber cement demands precise cutting and sealing, which extends installation. For a typical 1,800 sq ft home, expect 12–18 hours for Everlast and 18–28 hours for Hardie, assuming standard crew size. Assumptions: crew size, wall height, and weather.
Additional & Hidden Costs
Hidden costs can change the final bill: improved drainage around foundations, extra flashing, or replacement of damaged sheathing behind siding. If old siding is difficult to remove or there is extensive rot, disposal and replacement costs rise. For fiber cement, specialized tools and respiratory protection may be required, adding to equipment costs.
Real-World Pricing Examples
Basic scenario: 1,400 sq ft, Everlast siding, standard trim, no gutters. Materials $2.50/sq ft, install $6.50/sq ft. Total roughly $11,400. Labor ~14 hours, per-hour rates apply. Assumptions: single-story, standard windows.
Mid-Range scenario: 1,800 sq ft, Hardie fiber cement, upgraded color, basic trim. Materials $5.50/sq ft, install $10.00/sq ft. Total around $19,800. Labor ~20 hours, higher due to fiber cement cutting. Assumptions: two-story, mild weather window.
Premium scenario: 2,400 sq ft, Everlast with premium texture, full wrap around trim, upgraded flashing. Materials $4.00/sq ft, install $9.50/sq ft. Total about $25,000. Labor ~25 hours, advanced details add time. Assumptions: high-end finish, extended warranty.
