Buyers typically pay for labor, electrical upgrades, and delivery logistics when installing a double oven. The main cost drivers are electrical work, cabinet adjustments, and removal of the old unit. The price range varies by unit size, circuit requirements, and regional labor rates.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Labor & Installation | $400 | $900 | $1,800 | Includes removal of existing unit and cabinet adjustments |
| Electrical Work | $150 | $500 | $1,200 | New circuit (40–50A) or upgrade; wiring and breakers |
| Permits & Codes | $0 | $100 | $300 | Depends on local requirements |
| Delivery & Removal | $40 | $120 | $300 | Transport to kitchen and haul away old unit |
| Materials & Accessories | $80 | $250 | $600 | Mounting brackets, wiring kits, filler panels |
Assumptions: region, specs, labor hours.
Overview Of Costs
Typical total project ranges for a standard built-in double oven installation fall between $1,070 and $3,000, assuming a wide range of cabinets, electrical work, and delivery scenarios. A common per-unit pricing framework estimates $400–$1,200 per oven for labor plus $150–$500 for electrical work, with extra charges for permits or cabinet modifications. Assumptions: region, specs, labor hours.
Per-unit pricing considerations often show $500–$900 for labor per oven when two units are installed in a dual-cook setup, plus $100–$350 per oven for wiring and electrical upgrades. When both ovens share a single 240V circuit with a high-amp feed, total electrical costs can approach the upper end of the range. Assumptions: region, specs, labor hours.
Cost Breakdown
Table shows how total cost distributes across major components.
| Category | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials | $80 | $250 | $600 | Brackets, filler panels, wiring kits |
| Labor | $400 | $900 | $1,800 | Installation, cabinet adjustments |
| Electrical | $150 | $500 | $1,200 | Circuit upgrade and wiring |
| Permits | $0 | $100 | $300 | Local code compliance |
| Delivery/Disposal | $40 | $120 | $300 | Transport and old unit haul-away |
| Warranty & Overhead | $20 | $60 | $150 | Company warranty and overhead |
What Drives Price
Key cost drivers include electrical requirements and cabinet fit. The need for a dedicated 240V line, amperage (40–50A), and whether existing wiring can be reused influence total labor and materials. Additional drivers include oven size (27″ vs 30″), weight, and whether a cabinet spacer or trim kit is needed. A high-pitch cabinet or custom panel work adds to both time and materials. Assumptions: region, specs, labor hours.
Ways To Save
Smart budgeting can trim upfront costs without sacrificing safety or performance. Consider pairing the installation with an existing kitchen upgrade to consolidate labor, requesting a fixed-price quote to avoid hourly overruns, and evaluating whether a pre-wired alternative or shorter run length reduces electrical expenses. Assumptions: region, specs, labor hours.
Regional Price Differences
Prices vary by market; three representative zones show distinct deltas. Urban areas typically face higher labor rates than suburban and rural regions, with variation driven by local demand and permit costs. Suburban markets often align with national averages, while rural estimates may be lower due to reduced labor competition. In all cases, electrical upgrade requirements mostly drive the spread.
Real-World Pricing Examples
Three scenario cards illustrate typical quotes.
- Basic: One 27″ double oven, no major cabinet modification; standard 40A circuit; minimal delivery. Labor: 4–6 hours; Electrical: $250; Total: $1,070–$1,400.
- Mid-Range: 30″ double oven, moderate cabinet adjustments, dedicated 50A circuit; basic trim kit included. Labor: 6–8 hours; Electrical: $450; Permits: $50–$150; Total: $1,500–$2,000.
- Premium: Two double ovens in quilted panel setup; full cabinet fabrication, high-end wiring, and disposal service; 50A or higher circuit. Labor: 8–12 hours; Electrical: $800–$1,200; Permits: $150–$300; Total: $2,400–$3,600.
Assumptions: region, specs, labor hours.
data-formula=”labor_hours × hourly_rate”>
