Crush and Run price typically includes material, delivery, and installation, with costs driven by location, depth, and access. This article breaks down current pricing in USD and shows practical ranges for a standard driveway project.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Material (crush and run gravel) | $1.00 | $1.50 | $3.00 | Per sq ft for the finished depth |
| Delivery | $50 | $200 | $600 | Distance-based, typical 10–25 miles |
| Labor (installation) | $0.90 | $2.00 | $3.50 | Per sq ft, compacted |
| Equipment use | $0.10 | $0.40 | $1.00 | Per sq ft, roller and loader |
| Site prep | $150 | $600 | $1,500 | Includes grading and edging |
| Permits (if required) | $0 | $50 | $300 | Depends on local rules |
| Total project range (1,000 sq ft) | $1,900 | $3,800 | $7,200 | Assumes 3–4 inches depth |
Typical total cost for a 1,000 square foot project
Crush and Run price for a standard 1,000 sq ft driveway at 3 inches of depth usually ranges from $1,900 to $7,200, with midpoints near $3,800. Prices vary by regional material costs, access, and required drainage. Assumptions: suburban labor rates, standard crush and run mix, normal vehicle access.
| Scenario | Low | Average | High | Notes |
|---|---|---|---|---|
| Rural property, 12 miles from supplier | $2,100 | $3,900 | $6,800 | Delivery cost rises with distance |
| Suburban lot with 6-inch edge edging | $2,800 | $4,300 | $7,000 | Edge and prep add power equipment time |
| Flat site, no drainage work | $1,900 | $3,600 | $5,800 | Minimal grading |
The major cost components split between materials, labor, and logistics. Understanding each part helps compare bids and spot where savings are possible.
| Component | Low | Average | High | What affects it |
|---|---|---|---|---|
| Materials | $1.00 | $1.50 | $3.00 | Stone grade, supplier, blend ratio |
| Labor | $0.90 | $2.00 | $3.50 | Crew size, onsite efficiency |
| Delivery | $50 | $200 | $600 | Distance and access restrictions |
| Equipment | $0.10 | $0.40 | $1.00 | Rollers, skid steer, trucks |
| Site prep | $150 | $600 | $1,500 | Grading, edging, compaction |
| Permits | $0 | $50 | $300 | Local requirements |
Two key drivers strongly shift quotes: depth of the crushed stone layer and site access. Depth increases material and compaction costs quickly, while difficult access can double delivery and labor time in tight driveways.
For a 2-inch layer the per-square-foot price may run about $1.25–$2.50, while a 4-inch lift commonly lands around $2.50–$4.50 per sq ft. Assumptions: typical residential lot, standard edging, mid-range material.
Costs can swing 15–40% by region due to material supply and labor rates. Midwest averages often sit between $2.50 and $4.00 per sq ft for 3 inches, while coastal West can push higher on delivery and permits.
A two-person crew with a compact tractor typically reduces time, but aggressive sites may require three workers and a skid steer. Assumptions: standard crew, weekday work window.
Control scope by sticking to core driveway stone, limit edging upgrades, and compare bids that separate materials from labor. Bundling delivery with material purchase can lower overall costs and reduce scheduled downtime.
Drainage adds cost, as does additional compaction, erosion control, or expansive base preparation. Factor these into bids only if site conditions demand them.
- Bid A: Materials $1,300; Labor $2,000; Delivery $150; Total $3,450
- Bid B: Materials $1,800; Labor $2,600; Delivery $250; Total $4,650
- Bid C: Materials $2,100; Labor $2,900; Delivery $350; Total $5,350
Prices per square foot often look like $1.20–$2.50 for 2 inches, $2.00–$4.00 for 3–4 inches, with regional modifiers. Per-square-foot guidance helps when planning multiple lots or future extensions.
Assuming 3–4 hours of site prep per 1,000 sq ft and a $60–$90 hourly rate, labor contributes approximately $180–$360 in that scope.
