Buyers typically pay for a 24′ LVL beam based on length, load rating, thickness, and delivery. Pricing also varies by region, supplier, and whether additional services like cutting or hardware are needed. The following sections break down current costs and provide a practical pricing snapshot for planning a project.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| LVL Beam (24′, standard 1.75″ x 11.875″) | $180 | $320 | $780 | Prices include beam only; delivery may vary. |
| Delivery | $40 | $90 | $180 | Depends on distance and access. |
| Cutting/Processing | $20 | $60 | $150 | Per cut or set of cuts, if required. |
| Hardware & Supports | $10 | $40 | $120 | Joists hangers, connectors, and posts as needed. |
| Permits / Fees | $0 | $40 | $200 | Only where local rules apply. |
Overview Of Costs
Cost estimates for a 24′ LVL beam reflect itemized pricing and typical project ranges. The total project range commonly falls between $290 and $1,310, with per-foot pricing roughly $7.50 to $32.50 depending on grade, species, and required supports. Assumptions include standard residential use, no specialized joists or engineered options, and typical lead times.
Cost Breakdown
The following table shows a practical split of costs for a single 24′ LVL beam project. The figures assume standard installation work, basic mounting hardware, and no unusual site conditions.
| Category | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials | $180 | $320 | $780 | Beam plus standard options. |
| Labor | $70 | $220 | $660 | Includes handling and basic installation. |
| Delivery | $40 | $90 | $180 | Distance-based. |
| Permits | $0 | $40 | $200 | As required by local code. |
| Accessories | $10 | $40 | $120 | Hangers, fasteners, supports. |
| Contingency | $0 | $10 | $60 | Rounding and adjustments. |
What Drives Price
Price hinges on beam grade, species (e.g., SPF vs. structural plywood-lam LVL), and the required load rating or deflection control. Key drivers include load capacity (kips), section thickness, and any necessary end supports. Additional factors are delivery distance, site access, and whether the beam must be cut to length or pre-cut to fit. For example, higher-grade LVL with greater bending strength increases material cost, while complex on-site handling can raise labor and equipment charges.
Ways To Save
Several practical steps help control total expense without compromising safety. Compare quotes from multiple suppliers, consider standard stock lengths before requesting special orders, and check for bundled services (delivery plus cuts). Ask about rough-cut options and regional rebates or incentives that may apply. If feasible, align the beam replacement with off-peak delivery windows to potentially reduce delivery charges, and verify whether permits are required before ordering to avoid last-minute fees.
Regional Price Differences
Prices show modest regional variation across the U.S. In the Northeast, higher labor rates can push total costs upward, while the Midwest and Southeast may offer more favorable delivery and material pricing. Delivery distances and local supply competition significantly influence final numbers, with Rural areas sometimes facing higher trucking fees but lower labor costs compared to urban markets.
Labor & Installation Time
Installation time for a 24′ LVL beam typically ranges from 2 to 6 hours, depending on site access, support configuration, and whether temporary shoring is needed. Assumptions: standard residential joists, no complex framing, single beam replacement. Labor costs reflect crew size and regional rates, commonly $60–$120 per hour for skilled labor.
Real-World Pricing Examples
Three scenario cards illustrate common outcomes. Each uses standard assumptions and notes when costs may shift with site specifics.
Basic a 24′ LVL Beam
Specs: standard grade LVL, single beam, minimal cutting, suburban site. Labor: 2.5 hours. Materials: $180. Delivery: $60. Total: $350. $/ft: $14.58. Assumptions: suburban with basic access.
Mid-Range 24′ LVL Beam
Specs: enhanced grade LVL, minor processing, standard delivery. Labor: 4 hours. Materials: $320. Delivery: $90. Total: $520. $/ft: $21.67. Assumptions: standard access, no permits needed.
Premium 24′ LVL Beam
Specs: high-capacity LVL, multiple cuts, expedited delivery, potential permit fees. Labor: 6.5 hours. Materials: $680. Delivery: $180. Permits: $200. Total: $1,310. $/ft: $54.58. Assumptions: urban site with access challenges.
Assumptions: region, specs, labor hours.
Prices At A Glance
For planning, expect a broad price corridor: beam-only costs roughly $180–$780, with total project ranges typically $290–$1,310 after delivery, processing, and basic hardware. Per-foot estimates span about $7.50–$32.50, reflecting grade, span, and install requirements. Always confirm the exact specifications with the supplier before ordering.
