Prices for a 6-foot stockade fence vary by wood type, length, labor, and location. This article outlines typical cost ranges and the main drivers behind the price, so buyers can budget accurately for a new fence project.
Assumptions: Midwest labor rates, standard pressure-treated pine boards, 6-foot privacy panel style, standard gate, concrete footer where required.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Installed fence per linear foot | $15 | $22 | $30 | Includes fence boards, rails, posts, and basic fasteners |
| Perimeter total (100 ft) | $1,500 | $2,200 | $3,000 | Assumes single gate and standard access |
| Posts (wood, 4×4, set in concrete) | $8 | $12 | $20 | Includes set and concrete |
| Gates (4-foot to 6-foot) | $150 | $350 | $800 | With hardware |
| Permits and inspections | $0 | $150 | $600 | Varies by city |
| Removal of old fence | $0 | $5 | $15 | Per linear foot |
Typical price range for a 6-foot stockade fence installed
Most homeowners pay between $1,500 and $3,000 for a 100-foot stretch of 6-foot stockade fencing installed in residential settings. The typical project uses pressure-treated pine, standard posts set in concrete, and one gate. Expect the price to rise above this band if premium woods (cedar, redwood), ornamental hardware, or multiple gates are added. Assumptions: single-section layout, level ground, standard access, no need for retaining walls.
Major cost components in the stockade fence quote
The quote breaks down into four to six major parts. Labor and materials usually form the largest shares, followed by posts and hardware, then any permits or disposal. The table below shows a representative split for a 100-foot project with one gate.
| Component | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials (boards, rails, fasteners) | $600 | $1,100 | $1,900 | Wood type varies |
| Labor | $600 | $1,100 | $1,900 | Crew of 2-3, 1 day |
| Posts and concrete | $240 | $420 | $720 | 4×4 posts, footings |
| Gate hardware | $60 | $180 | $320 | Hinges, latch |
| Permits/fees | $0 | $150 | $600 | Varies by locality |
| Delivery/Disposal | $0 | $50 | $150 | Materials drop-off and old fence removal |
How panel length, material, and gates affect price
Longer runs add linear foot costs, while material grade changes price per board. A few concrete cost drivers are shown here: cedar or redwood increases price by roughly 30% to 70% over pressure-treated pine, and a second gate can add $150–$800. Perimeter length, ground slope, and access ease also shift labor hours. Assumptions: standard gate size 4-6 feet, level terrain.
Variables that shift the final quote for a 6-foot stockade fence
Two primary drivers stand out. First, distance and layout complexity: longer, irregular perimeters can push total by 20%–40%. Second, soil and drainage: poorly draining soils or required trenching raises costs for posts and footings by 15%–25%. Regional labor rates drive large swings in total pricing.
Ways to reduce the price on a 6-foot stockade fence project
Smart scoping can cut costs. Keep the run straight and avoid irregular angles, install a single gate, and reuse existing posts if feasible. Consider budget-friendly materials, plan installations in mild months, and obtain multiple quotes to compare labor rates. Assumptions: standard 6-foot panels, no specialty hardware.
Regional price differences for stockade fencing in the U.S.
Prices vary by region; the same 100-foot project can swing by 15%–25% between states due to labor costs and permit fees. In the Pacific Northwest, expect higher overall costs due to lumber demand; in the Midwest, rates tend to be mid-range. Typical regional delta estimates help set realistic expectations.
Labor considerations: crew size and installation time
A 100-foot fence commonly takes 1–2 days for a two-person crew or longer with a larger crew or difficult terrain. Hourly rates usually range from $50 to $75 per hour per worker, depending on region and experience. A standard project estimates 16–40 labor hours for a full install.
Surface prep, posts, and hardware per unit pricing
Per-unit costs emphasize posts, concrete, and fasteners. Posts typically cost $8–$20 each when installed with concrete, while gates range $150–$800 depending on size and hardware. Budget for basic concrete mix and anchoring when determining per-foot pricing. Assumptions: 4×4 posts, standard hinge hardware.
Practical steps to compare quotes for a 6-foot stockade fence
To compare quotes effectively, request a breakdown showing: materials, labor, posts, gates, permits, and disposal. Ask for the same scope across bidders to avoid apples-to-oranges comparisons. Include a per-foot and per-post summary so the math is transparent. Assumptions: same fence height, same post spacing, and one gate.
