Prices for 5/8 Tongue and Groove plywood vary by sheet type, grade, and regional labor costs. The cost you see typically reflects the panel core, tongue and groove profile, and any finish or treatment. This guide shows current price ranges in USD and explains the main drivers behind the cost of 5/8 in Tongue and Groove plywood.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| 4×8 sheet, 5/8″ Tongue & Groove plywood | $25 | $40 | $65 | Interior rated, standard grade |
| Installed cost per sheet (including labor) | $120 | $160 | $210 | Residential installation, standard conditions |
| Per linear foot (paneling runs) | $2 | $3.50 | $5 | Depends on profile and waste |
| Delivery & handling per shipment | $20 | $40 | $80 | Local delivery distance matters |
What buyers usually pay for 5/8 Tongue and Groove Plywood
Typical total cost for a small project is the sum of materials plus installation. Material costs commonly range from $25 to $65 per 4×8 sheet, with installation adding roughly $120 to $210 per sheet depending on access and prep. For projects that require multiple sheets, buyers often combine pricing for bulk discounts or staged delivery. Assumptions: standard indoor use, normal access, mid-range grade plywood, and a modest job scope with no tricky cuts.
Cost components that appear in a 5/8 in Tongue and Groove plywood quote
Pricing is broken into major parts to show where money goes. Materials, labor, and delivery/handling account for most of the total, while permits, waste disposal, and overhead add smaller charges. The table below uses a 4×8 sheet basis and moderate access conditions.
| Component | Typical Range | Per-Sheet Basis | Notes |
|---|---|---|---|
| Materials | $25-$65 | $25-$65 | Core plywood, tongue/groove profile, finish |
| Labor | $100-$210 | $100-$210 per sheet | Removal, prep, install, fastening |
| Delivery/Handling | $20-$80 | $20-$80 | Distance and access dependent |
| Waste Disposal | $0-$20 | $0-$20 | Carting off scraps |
| Overhead & Profit | $10-$40 | $10-$40 | Contractor markup |
Key variables that change the 5/8 in Tongue and Groove plywood price
Several factors can swing the final bill. Sheet grade and face veneer quality directly affect material cost, while region and access for installation influence labor and delivery charges. Heavier or specialty finishes add premium costs. Size of the project, whether more than a few sheets are needed, and whether the subfloor or wall surface needs extra prep are also important.
Ways to reduce the price of 5/8 in Tongue and Groove plywood
Smart budgeting tips avoid unnecessary upgrades. Choose standard interior grade panels and limit specialty finishes to reduce cost per sheet. Consolidate orders to minimize delivery trips, verify existing subfloor flatness before installation, and compare bids from multiple local suppliers. If a small project, consider using fewer cuts and simple layouts to reduce waste.
Regional price differences for 5/8 in Tongue and Groove plywood across the U.S.
Prices shift by market area. Coastal regions often run higher on materials and labor, while Midwest and Southern markets may be more price-competitive. Typical delivery surcharges rise with distance from the supplier, potentially adding $10–$30 per sheet in remote zones. Regional price deltas for a 4×8 sheet commonly span $20 from low to high within the same month.
Installation time, crew size, and labor hours for 4×8 sheets
Installation pace depends on the surface and layout. A small crew typically spends 1.5–2.5 hours per sheet for basic installs, including acclimation, fastening, and edge fitting. For larger jobs, crews of 2–4 workers reduce time per sheet, but labor costs scale with the total hours. Expect total labor per sheet in the $100–$210 range under standard conditions.
Delivery, handling, and waste disposal for 5/8 in Tongue and Groove plywood
Delivery charges are usually per shipment and distance-based. Per-shipment delivery often falls between $20 and $80, with additional fees if long carries or curbside unloading are required. Proper waste handling adds minimal cost if scraps are reused, but disposal fees can rise to $10–$20 per bag in some markets.
Real-world quote example for 4×8 sheets installed
Scenario: 8 sheets of 5/8″ Tongue and Groove plywood installed over a roughed subfloor in a single room. Materials: 8 sheets at $40 each. Labor: 8 sheets at $150 average. Delivery: 1 trip at $40. Tax: 6%. Total estimate sits around $1,260 to $1,480 depending on access and waste. This illustrates how material and labor blend into the installed cost per sheet.
Per-unit pricing and how it translates to a full project
When budgeting, two common units appear. Per sheet pricing stays in the $25-$65 range, while installed cost per sheet typically runs $120-$210 plus delivery. For runs longer than a single room, per-foot or per-run pricing helps project planners compare options. A straightforward rule is to multiply the installed per-sheet cost by the number of sheets, then add delivery and any disposal fees.
