Plywood thickness 5/8 inch is a common choice for subflooring, sheathing, and cabinet panels. Buyers usually pay for the sheet itself plus local labor, delivery, and any waste or special finish. The cost per sheet varies by grade, veneer, sheet size, and regional market conditions, with typical ranges shown below.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| 5/8″ plywood sheet (4×8) | $28 | $40 | $60 | Standard exterior or interior, A/B grade may cost more |
| Delivery per sheet | $0 | $6 | $15 | Local distance affects price |
| Install labor (per sheet) | $0 | $15 | $40 | Includes basic handling, not installation of subflooring |
| Waste/overage (sheet count extra) | $0 | $5 | $12 | QA for exact cuts |
| Finishing or special veneer | $5 | $12 | $25 | Birch or tropical veneer adds cost |
Typical price for the exact item: 5/8 inch plywood per sheet
Common total price for a single 4×8 sheet ranges from $40 to $60, depending on grade and veneer. For interior use with standard grade, expect closer to the $40 range; exterior-rated or higher-grade veneers push toward $60 or more. Regional factors such as port access, import costs, and supplier volume can shift prices by ±15% in a given month. Assumptions: standard 4×8 sheet, midwestern or southern labor markets, normal access and no rush delivery.
Major cost components broken out in a quote
A typical quote splits into materials, labor, and delivery. Materials dominate the price for a single sheet, while labor and delivery add smaller but noticeable amounts depending on accessibility and job scope. The following table summarizes a representative breakdown.
| Component | Low | Average | High | Why it matters |
|---|---|---|---|---|
| Materials (5/8″ plywood, 4×8) | $28 | $40 | $60 | Grade and veneer drive the range |
| Labor (install/surface prep) | $0 | $15 | $40 | Labor rate varies by region |
| Delivery | $0 | $6 | $15 | Distance and access impact |
| Waste/extra sheet provisioning | $0 | $5 | $12 | Cuts and fit adjustments |
| Finishing/veneer upgrade | $0 | $5 | $25 | Premium finishes add cost |
Key price drivers: grade, veneer, and moisture rating
Grade quality and veneer type are the dominant price levers for 5/8″ plywood. Interior panels in a basic CD or C grade run lower than exterior or marine-grade sheets, while premium veneers (birch, maple) push the price upward. Moisture rating (exterior vs interior) also changes the base cost by about 10-25% depending on supplier stock. Assumptions: standard 4×8 sheet, typical interior use in residential projects, normal supply chain conditions.
Regional price differences you should expect
Prices vary by region due to freight, demand, and local taxes. In the U.S., coastal markets and regions with higher lumber costs can see sheets run 10-20% above inland averages. Midwestern markets often sit near the national average, while sunbelt regions with strong construction activity may experience tighter price ranges and occasional surcharges. Assumptions: 4×8 sheets, standard freight within 100 miles.
Size and grade combinations that shift costs
Choosing interior vs exterior grades changes price per sheet by 20%–40% for some brands. A 4×8 sheet of 5/8″ exterior plywood with higher-grade face veneer can cost substantially more than an interior P5 or CDX option. If you anticipate moisture exposure, plan for the higher price tier and potential fasteners and sealant costs. Assumptions: typical kitchen or subflooring use, standard fasteners, no long-haul delivery.
How to estimate a multi-sheet project cost
Scale matters: per-sheet pricing helps estimate total cost for a project. Multiply the sheet price by the number of sheets, add estimated delivery and waste, then include a modest labor allowance if installation is needed. For 15 sheets, a practical range might be $600–$900 for materials, plus $60–$180 for delivery and $225–$600 for labor if installation is required. Assumptions: 4×8 sheets, midrange grade, standard access, no rush.
Ways to reduce the price without sacrificing too much value
Controlling scope and material choice can trim costs. Consider using interior-grade plywood for dry environments, purchasing in bulk to secure a lower per-sheet price, and coordinating delivery with other projects to reduce trips. Avoid premium veneers for arbitrary cuts, and plan for efficient layouts to minimize waste. Assumptions: standard room remodeling project, no custom finishes, midweek delivery.
Per-rectified costs: regional vs national price impression
Understanding local markets helps prevent sticker shock. If a local supplier quotes 5/8″ plywood at $52 per sheet versus a regional average of $40, factor in delivery and potential volume discounts. In some markets, builder supply stores offer loyalty rebates or contractor pricing that can shave 5-15% off the stated sheet price. Assumptions: single-family home rehab, 4×8 sheets, typical contractor pricing model.
