For buyers researching 1×6 tongue and groove pine, price and per-unit costs are the key factors. This article presents concrete price ranges, explains drivers, and shows how to compare quotes for a typical room or project. The cost section uses practical estimates in dollars to help budgeting and planning.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| 1×6 T&G Pine board (per linear foot) | $0.60 | $0.95 | $1.40 | Common grade, standard knotting |
| Premium kiln-dried 1×6 T&G (per linear foot) | $1.00 | $1.40 | $2.00 | Better straightness, fewer defects |
| Installation labor (per hour, carpenter) | $38 | $58 | $85 | Includes fastening and alignment |
| Labor to install per square foot | $2.50 | $4.00 | $6.50 | Assumes 8–12 ft ceilings, basic substrate |
| Delivery (inside urban area, per mile) | $20 | $40 | $100 | Distance-based |
Assumptions: Midwest labor rates, standard pine, typical 8–12 ft ceilings, no specialty finishes.
Price Range by Common Grades for 1×6 Tongue and Groove Pine
Buyers typically see prices between $0.60 and $1.40 per linear foot for standard grade 1×6 T&G pine, with kiln-dried, higher-grade boards ranging from $1.00 to $2.00 per linear foot. The total project cost depends on room length, waste, and finish choices, but the per-foot figures provide a practical budgeting baseline.
Assumptions: standard 1×6 boards, typical knot patterns, no premium grade finishes, standard nail or clip fasteners.
Major Cost Components in a 1×6 Tongue and Groove Pine Quote
Material costs form the largest share, followed by labor for installation and delivery. A typical quote breaks down into four to five line items to help compare bids side by side.
- Materials: per linear foot price for standard or premium pine
- Labor: hours × hourly rate for installation
- Delivery/Delivery/Receiving: regional distance charges
- Waste/Prep: minor extra for cut-offs or surface prep
- Finishes (optional): stain, sealant, or clear coat if requested
| Cost Component | Typical Range | Notes |
|---|---|---|
| Materials | $0.60–$2.00 per linear ft | Depends on grade and kiln-drying |
| Labor | $38–$85 per hour | Field conditions and crew size affect rate |
| Delivery | $20–$100 | Distance and access |
| Finish / Sealant | $0.25–$0.75 per linear ft | Optional |
| Waste allowance | 5–10% | Estimates for cuts and mistakes |
Formula example: estimated cost = (board length in ft × price per ft) + (labor hours × hourly rate) + delivery + finish.
Regional Variations That Impact 1×6 T&G Pine Pricing
Prices shift with geography due to lumber markets, supply chain, and labor hours. In the Northeast, expect higher delivery and labor ranges; in the Southeast, material costs may be slightly lower but shipping to remote areas can raise delivery fees. Regional availability of pine species also influences price, with kiln-dried stock priced higher in drought-prone regions.
Assumptions: standard pine species, no specialty finishes, typical access.
Labor Factors That Move the Quote for 1×6 Pine T&G
Labor time scales with room size, ceiling height, and planned pattern alignment. A small room with 8 ft ceilings typically requires fewer hours than a large, vaulted space or complex ceiling layout. Labor can range from $2.50 to $6.50 per square foot installed, depending on substrate prep and fastening method.
Assumptions: standard substrate, no intricate profiles, basic fastening hardware.
Material Details: Choosing Pine Grades for 1×6 T&G
Standard grade often has visible knots and minor defects; premium grades deliver smoother surfaces with fewer knots. Kiln-dried pine reduces warping risk and provides consistent nail-hold, but adds cost per linear foot. For budget projects, standard grade commonly suffices if boards are trimmed and planed before installation.
Assumptions: indoor, dry conditions, climate control, and typical household humidity.
Per-Unit and Per-Project Pricing for 1×6 T&G Pine
Per-linear-foot pricing is most common, but per-square-foot estimates help when planning wall or ceiling installations. For a 100 sq ft wall, using 8 ft boards with 1×6 T&G, expect material costs in the range of $60–$140 per 100 sq ft for standard grade, plus labor and finishing if chosen.
Assumptions: 8 ft board length, standard layout, no specialty pattern.
Ways to Reduce 1×6 T&G Pine Costs Without Compromising Structure
Scope control, material choices, and timing are practical levers. Consider using standard grade pine, reduce waste through precise cutting, schedule installs in non-peak seasons, and compare quotes from nearby suppliers to minimize delivery charges. Bundling ceiling and wall projects can also yield labor savings.
Assumptions: midwest region, typical labor market, standard nails or clips.
Real-World Quote Scenarios for 1×6 Tongue and Groove Pine
Scenario A: 120 linear ft of standard grade T&G on a ceiling, 8 ft high. Material: $0.75/ft, Labor: $3.50/ft, Delivery: $40. Total: about $128–$208 per linear ft including finish as optional.
Scenario B: 180 linear ft on walls, premium grade kiln-dried, no finish. Material: $1.50/ft, Labor: $5.00/ft, Delivery: $70. Total: roughly $205–$350 per linear ft with finish.
Scenario C: Small 80 linear ft project in a rural area, standard grade, basic install. Material: $0.65/ft, Labor: $2.75/ft, Delivery: $60. Total: around $120–$190 per linear ft.
Assumptions: standard environment, ordinary fastening hardware, basic square-ended joints.
