Prices for 1×6 redwood lumber vary by grade, region, and quantity. This article outlines typical cost ranges for the exact keyword and breaks down what drives the price, including finish, delivery, and waste. Buyers can expect a range rather than a fixed point, with clear per-unit pricing where relevant.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Per linear foot | $1.20 | $2.10 | $3.50 | Common grades and moisture levels |
| Per 8 ft board | $9.60 | $16.80 | $28.00 | Typical residential lengths |
| Per board foot | $2.40 | $4.20 | $7.00 | Board-foot unit pricing |
| Delivery (5–50 miles) | $50 | $100 | $180 | Regional fuel and distance drive |
| Waste/kerf (slack stock) | $0.50 | $1.50 | $4.00 | Rough cuts and offcuts |
Assumptions: Midwest labor rates, standard moisture content, typical 1×6 nominal size (actual 3/4″ x 5.5″). Prices reflect new lumber from regional suppliers, not recycled or specialty stock.
Typical Price for 1×6 Redwood Lumber by Size and Grade
Buyers usually pay a total price that blends grade, moisture, and length. For common DIY work, expect 1×6 redwood priced at about $1.20 to $3.50 per linear foot, translating to roughly $9.60 to $28 for an 8 ft board. If priced by board foot, the range is about $2.40 to $7.00 per board foot, depending on grade and processing. Higher grades with tight grain or clear stock push toward the upper end.
Assumptions: standard residential grade, kiln-dried stock, nominal 1×6 with typical resin content. Slight regional premium or discount may apply for nearby mills or large-volume purchases. Low-end pricing reflects common stock with standard moisture content and minimal defects.
Cost Components Across a 1×6 Redwood Lumber Quote
| Component | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials | $1.00/ft | $2.00/ft | $3.50/ft | Grade, moisture, and stock type |
| Labor | $0.75/ft | $1.25/ft | $2.00/ft | Cutting, measuring, and prep |
| Delivery/Distribution | $50 | $100 | $180 | Distance-based |
| Waste/Discard | $0.25/ft | $0.75/ft | $1.50/ft | Kerf and defect clearance |
| Permits/Taxes | $0 | $5 | $20 | Local sales tax or permit fees if required |
| Delivery packaging | $0 | $0.50/ft | $1.00/ft | Protective wrap, bands |
Formula example: total = (board feet × price per board foot) + delivery + tax. The components help explain variations between suppliers.
How Finish, Grade, and Moisture Change the Price
Clear or radiata-grade redwood with minimal knots commands a higher price than standard construction grade. Moisture content also shifts pricing, with kiln-dried stock typically costing more than green stock. Expect roughly 15% to 40% price differentials between select-grade stock and utility-grade lumber. kiln-dried materials may cost 10%–25% more than air-dried equivalents, depending on supplier and region.
Regional Price Variations Across the United States
Prices fluctuate by region due to availability, freight, and demand. In the West Coast, high demand and transport costs can push per-foot figures toward the upper end, while the Southeast may offer slightly lower base prices due to local mills. On average, regional deltas can reach 10%–25% between neighboring markets. Buyers in rural areas may pay a small premium for limited supply or delivery surcharges, while urban markets can see steeper delivery fees.
Quantity Impacts: Bundles Versus Individual Pieces
Buying in bundles reduces per-foot costs but introduces storage considerations. A full 1×6 bundle of common lengths (8 ft or 10 ft) can lower the per-board price by 5%–12% compared with buying single boards. For small projects, singles may cost more per board due to higher handling fees.
Labor Time and Cutting to Lengths for Finished Runs
If a project requires cut-to-length or angled cuts, labor adds to the per-board cost. Typical rates for skilled carpentry work range from $75 to $125 per hour, with 1×6 cuts adding 5–15 minutes per board depending on complexity. Expect roughly $5–$15 per board in labor for standard cuts on a small project.
Delivery, Storage, and Seasonal Availability
Delivery costs scale with distance and fuel prices, often ranging from $50 to $180 per shipment for typical residential distances. Seasonal price spikes may occur in spring and summer when outdoor projects surge demand. Plan ahead to avoid rush fees or last-minute delivery surcharges.
Quality Alternatives: Reclaimed vs New Stock
Reclaimed redwood can offer cost savings but introduces variability in size, moisture, and defects. New stock provides consistent dimensions and moisture control, which reduces waste and miscuts. Reclaimed stock often costs 15%–40% less per linear foot but may require extra processing time.
Price-Check Plan: How to Compare Quotes
When comparing quotes, look for price per linear foot, per board foot, and included waste. Ask providers to break out materials, labor, delivery, and any disposal charges. A side-by-side table helps surface hidden costs and ensures apples-to-apples comparisons.
Mini Examples: Realistic Quote Scenarios
Scenario A: 8 boards of 8 ft length, 1×6 redwood, construction-grade, kiln-dried, local supplier. Materials $2.50/ft, labor $1.25/ft, delivery $75. Total per board around $24.50; total for 8 boards about $196. Scenario B: Premium clear stock, same length, higher grade with minimal knots, kiln-dried. Materials $4.00/ft, labor $1.50/ft, delivery $100. Total per board about $44; total about $352.
Regional Snapshot: Quick Price Deltas by Market
West Coast markets may show higher base lumber rates than the Midwest due to transportation costs. The Northeast can reflect higher material premiums and tighter supply in the wake of regional mill consolidation. Color-coded region deltas help buyers budget with regional spreads of roughly 8% to 22% across major metro areas.
